1. In a three-phase induction motor
(a) iron losses in stator will be negligible as compared to that in rotor
(6) iron losses in motor will be neg¬ligible as compared to that in rotor
(c) iron losses in stator will be less than that in rotor
(d) iron losses in stator will be more than that in rotor
Ans: d
2. In case of 3-phase induction motors, plugging means
(a) pulling the motor directly on line without a starter
(b) locking of rotor due to harmonics
(c) starting the motor on load which is more than the rated load
(d) interchanging two supply phases for quick stopping
Ans: d
3. Which is of the following data is required to draw the circle diagram for an induction motor ?
(a) Block rotor test only
(b) No load test only
(c) Block rotor test and no-load test
(d) Block rotor test, no-load test and stator resistance test
Ans: d
4. In three-phase induction motors sometimes copper bars are placed deep in the rotor to
(a) improve starting torque
(b) reduce copper losses
(c) improve efficiency
(d) improve power factor
Ans: a
5. In a three-phase induction motor
(a) power factor at starting is high as compared to that while running
(b) power factor at starting is low as compared to that while running
(c) power factor at starting in the same as that while running
Ans: b
6. The vafcie of transformation ratio of an induction motor can be found by
(a) open-circuit test only
(b) short-circuit test only
(c) stator resistance test
(d) none of the above
Ans: b
7. The power scale of circle diagram of an induction motor can be found from
(a) stator resistance test
(6) no-load test only
(c) short-circuit test only
(d) noue of the above
Ans: c
8. The shape of the torque/slip curve of induction motor is
(a) parabola
(b) hyperbola
(c) rectangular parabola
(d) straigth line
Ans: c
9. A change of 4% of supply voltage to an induction motor will produce a change of appromimately
(a) 4% in the rotor torque
(b) 8% in the rotor torque
(c) 12% in the rotor torque
(d) 16% in the rotor torque
Ans: d
10. The stating torque of the slip ring induction motor can be increased by adding
(a) external inductance to the rotor
(b) external resistance to the rotor
(c) external capacitance to the rotor
(d) both resistance and inductance to rotor
Ans: b
11. A 500 kW, 3-phase, 440 volts, 50 Hz, A.C. induction motor has a speed of 960 r.p.m. on full load. The machine has 6 poles. The slip of the machine will be
(a) 0.01
(b) 0.02
(c) 0.03
(d) 0.04
Ans: d
12. The complete circle diagram of induetion motor can be drawn with the help of data found from
(a) noload test
(6) blocked rotor test
(c) stator resistance test
(d) all of the above
Ans: d
13. In the squirrel-cage induction motor the rotor slots are usually given slight skew
(a) to reduce the magnetic hum and locking tendency of the rotor
(b) to increase the tensile strength of the rotor bars
(c) to ensure easy fabrication
(d) none of the above
Ans: a
14. The torque of a rotor in an induction motor under running condition is maximum
(a) at the unit value of slip
(b) at the zero value of slip
(c) at the value of the slip which makes rotor reactance per phase equal to the resistance per phase
(d) at the value of the slip which makes the rotor reactance half of the rotor
Ans: c
15. What will happen if the relative speed between the rotating flux of stator and rotor of the induction motor is zero ?
(a) The slip of the motor will be 5%
(b) The rotor will not run
(c) The rotor will run at very high speed
(d) The torque produced will be very large
Ans: b
16. The circle diagram for an induction motor cannot be used to determine
(a) efficiency
(b) power factor
(c) frequency
(d) output
Ans: a
17. Blocked rotor test on induction motors is used to find out
(a) leakage reactance
(b) power factor on short circuit
(c) short-circuit current under rated voltage
(d) all of the above
Ans: d
18. Lubricant used for ball bearing is usually
(a) graphite
(b) grease
(c) mineral oil
(d) molasses
Ans: b
19. An induction motor can run at synchronous speed when
(a) it is run on load
(b) it is run in reverse direction
(c) it is run on voltage higher than the rated voltage
(d) e.m.f. is injected in the rotor circuit
Ans: d
20. Which motor is preferred for use in mines where explosive gases exist ?
(a) Air motor
(b) Induction motor
(c) D.C. shunt motor
(d) Synchronous motor
Ans: a
No comments:
Post a Comment